Easiest iPhone Glass Fix – WITH LASERS (Not clickbait)

Easiest iPhone Glass Fix – WITH LASERS (Not clickbait)

Articles Blog

So Apple’s going to hate me for making this
video. [Music] [Intro] So we all know that the back glass on the
new Apple iPhones are nearly impossible to repair. Even Apple themselves charge $550
to repair the back glass on an iPhone 10, and $600 to repair the back glass on an iPhone
11 and 11 Pro. It’s because the adhesive on their back glass is permanent. Now, they are
the only manufacturer that does this. Most manufactures have an adhesive that melts away
when it gets hot. And you can remove the back glass and repair the whole phone for like
$20. Removing the back glass is so hard and so
impractical, that’s why Apple charges $600 to replace it on the iPhone 11. In order for
a third party to remove the glass, it has to be subject to extreme temperatures. I’ve
even attempted to take the iPhones to the opposite end of the temperature spectrum and
use liquid nitrogen. Today though, I think we found something that’s more practical,
more repairable, and takes the pain out of removing the back glass. And it’s all done
with lasers. *laser sounds from the future* So this guy right here is an all-in-one multifunctional
laser machine that separates the back glass panel from the frame. Laser is an acronym
for Light Amplification by Stimulated Emission of Radiation. The red laser you see on top
of the glass right now is mostly just to figure out where the phone is located so we don’t
start lasering the metal frame of the phone. The laser is strong enough that it will actually
etch the metal so we’re trying to stay on just the glass surface. Once we switch over
to the wide laser, that’s where it’ll immediately start burning underneath the glass and separating
the glass from the metal frame which is exactly what we’re after…saving ourselves about
$500 or $600. Apple, if you’re watching, you can totally
buy one of these yourselves and drop your prices just a little bit. Now as the laser is pulverizing all the adhesive
underneath the glass, there is quite a lot of fumes that come out, so this is a vacuum
that sucks up the fumes from the burning adhesive, puts it through a filter and gets rid of the
burning adhesive smell. So this setup is from a company called Rewa,
and the software they have included with it works with most every major manufacturer.
But today we’re mostly worried about the iPhones because those are the hardest to repair. Each
design is already preprogrammed into the machine, all the way from the iPhone 10, the XR, the
8. The laser can separate the bezel from the screen as well as the back cover. And the
back cover on the X is what we’re doing today. Once I have the laser cutout selected, make
sure the phone’s set in the right spot, and then as soon as I hit “mark” the real
laser starts going. All the lasering you see happening right now
is happening in real time. None of this footage is sped up, and the whole process only takes
about 5 or 10 minutes. One pass with the laser underneath the glass gets rid of the bulk
of the adhesive and we can do a second pass just to remove any of the remaining. After
that, we can start removing the glass shards from the frame. A laser is a concentrated light beam, and
that concentrated light energy can be absorbed by some objects but not others. The laser
would pass through the glass just fine, but as soon as it hits the adhesive or the paint
on the back of the glass, the energy is converted to heat and starts pulverizing that paint
and the adhesive and turns it to dust. The high powered the laser beam, the more damage
it can do. And that is it. The laser has removed the
paint from underneath the glass so now the glass can fall away from the phone…for the
most part. So you can see here the laser design is cutting out the black portions and that
same design left the space for the wireless charging pad, as well as some sensitive bits
down here along the bottom. But those sensitive bits don’t have adhesive behind it holding
it to the glass panel so we’re just fine. So now that the laser has run it’s course,
we can take a look at the phone and see exactly what the laser has done. Taking a thin metal
pry tool inbetween the glass and the frame of the phone, I can slowly wedge the pieces
of glass out away from the back. Now in a perfect world, if the glass was completely
crack-less, the laser would have gone through and disintegrated the layer of adhesive between
the glass and the metal frame. You can see the pulverized paint and adhesive getting
on my fingers. The laser has literally burned everything underneath the glass to ash. But
where cracks appear in the glass, the laser refracts and doesn’t quite burn away the adhesive.
So there is still some prying to do, but it’s still much easier than any method we’ve tried
so far like extreme heat or liquid nitrogen. Now Apple has designed their phone in a way
where the glass panel sits underneath the camera lens, which poses a slight problem
for removal because that camera lens is welded to the frame and we want to leave that intact
to make it an easier repair. I’ll slowly chisel out the glass from underneath that welded
camera lens. Depending on what glass you buy there are third party glasses that fit underneath
this camera lens. I would recommend though that you buy a glass back that fits over the
camera lens. I’ll show you what I mean in a second. It just makes the repair much easier
cuz you don’t have to deal with that lens. So obviously I’m not a professional, I’m just
showing that the machine actually works. Someone who does this on a regular basis would do
a much cleaner job. But the technology is pretty fascinating. So now we have all the
glass shards away from the phone. The phone itself is still working, still functional
even though the back glass is removed. And now it’s time to add the new glass. It’ll
be as good as new. So when it comes time to select a piece of
glass for your phone, there’s a couple different options. One is that you can get the glass
with logo or without the logo. Apple’s been pretty anti-repair from the beginning, so
the vendors that sell the glass with the logo tend to disappear. If you’re a business doing
this on a regular basis, you might want to buy the glass without the logo, that way there’s
no copyright issues. It’s effectively de-branded you could say. The second thing to look out for is the cutout
of the glass. This white panel here you can see has the exact same cutout as the original
piece of glass, meaning we’d have to unweld the camera lens, put the glass down, and then
glue the camera lens back into place. Which is a much more difficult repair. So I recommend
buying the piece of glass that has a cutout large enough to slip over top of the camera
lens, and then sits down snugly inside of the frame. It’s a much easier repair and no
one’s really going to notice the difference. The adhesive I’m gong to use to adhere the
back glass to the phone is called E-8000. It’s a multi-purpose jewelry adhesive that
adheres glass and metal. I’ll apply it to the metal of the phone in basically the same
pattern that Apple used initially, and then do a super thin bead around the edge of the
phone before I clamp the glass down into place. There should be some seepage out around the
sides of the phone. This will help with water resistance even though I would not trust the
phone to be water resistant. And before the adhesive cures, which is about 4-10 minutes,
we’ll use some isopropyl alcohol to clean up the seepage from underneath the glass.
We want to make sure most of the overflow goo is gone before it has time to dry. It’s
easier to clean up when it’s wet. You might be asking yourself, what about water
resistance? Even though we’ve applied the glue in the same pattern that Apple applied
the original adhesive, water resistance isn’t something that you want to trust in the first
place, much less after it’s been broken and repaired. You should keep your phone away
from water either way. One thing to keep in mind though with this
laser machine is that the more cracks or the more shattered your phone is, the harder it
is for the laser to get through the glass. If your glass is pretty much obliterated,
the laser is going to go down and get refracted all over the place and not burn through the
adhesive underneath the glass. So the less cracked your back is, the easier it is for
this machine to work. Either way though, this machine brings the repair to a much more practical
and sustainable level. It’s doable. So each of these back glass panels costs about
$20. Now granted we did have to buy a $2000 machine, but for a repair shop doing a lot
of these on a regular basis, it’s a substantial improvement. And I’m a huge fan of where the
technology is headed. Lasers are pretty cool. So obviously this repair is a bit more complex
than your average teardown and requires some pretty expensive equipment, but it’s good
to know that the repair is possible and that there are people out there doing it for much
cheaper than Apple. Repair is an option. As much fun as playing with liquid nitrogen
with the King of Random was, using this laser separator is much easier. I have a feeling
these machines are going to get real popular real quick. I’ll leave a link for these down
in the video description so you can check out the current pricing. As with all technology,
I’m sure the price is going to go down as time progresses. If you have any questions leave them down
in the comments. Come hang out with me on Instagram and Twitter. And thanks a ton for
watching. I’ll see you around. These right here are all Apple Watch displays.
Every single one of them. My buddy’s done so many Apple Watch repairs that he turns
them into artwork.

100 thoughts on “Easiest iPhone Glass Fix – WITH LASERS (Not clickbait)”

  1. For the price of 5x Apple charges for you to replace your back glass, one can buy one of this machine. Can you imaging the career opportunity? Every smart phone repair shop will be happily purchase one of this.

  2. F-ck Apple. Impressive tech that needs to be utlized so that the little guy doesn't take it up the ass from a bazillion dollar company. n

  3. Not sure why we have this glass back trend began at all. First we had plastics/polycarbonate. Then came in metal which was the best in my opinion as it gave feeling of premium without the hassle of worrying about the fragility( Loved the 6S). These glass backs are too impractical. Gorilla Glass and all which some vendors use is also just some scratch resistance but can be easily shattered. I will just wait out till this stupid trend passes out and then buy a new device

  4. Apple: "Yes this is right…"
    Journalist: "But.. when exactly will I ever get into a laser fight to use my phone as a shield?"
    Apple: "Look at it this way, at least now you have a laser proof glass, which is one less thing to worry about."

  5. What's the wavelength of this laser? It can't be infrared because glass absorbs infrared so I assume it's ultraviolet? Perhaps a pulse laser?

  6. Does anybody know if there's a service that does this? Id like to pay for the service to fix it and not have to buy the whole machine. What would it be called? Laser fixing??

  7. 4:39 different phone to what he “repairs” I don’t know how that means the repair was fake ( which I doubt ) but why did they switch the phone

    5:20 this is what I mean. At 4:39 no screen/oled panel etc etc. But then BANG as soon as the back glass is removed the phones screen is back?


  8. Glass made back phone is hands down the most stupidest idea introduced on mobile phones in ages. And almost every producer makes it. Ffs

  9. Haha you think apple has a hard time getting the back off. Nah that's an excuse to why they can charge you so much.

  10. Uhm…is there any possibility to do that with a OnePlus? And do a clear, transparent back on it? Then I would do that!

  11. Pretty cool and informative video. Lots of hassle and expensive machine but nice to know for the price of roughly 3 repairs, you can buy a machine that can do it for a lot less.

  12. apple: charges $600 for a repair

    laser machine: probally costs thousands of dollars

    I guess it's not really easier lol to use the machine since it costs you far more than a iPhone lol

  13. Broke my phone talked about it calmed down then I see shit like this when I don’t look at shit like this. They are listening lmao

  14. Jerry: not clickbait
    Me, looking at the implication that the laser repairs the glass: ?
    Me, watching the actual video: so it was only sort of a lie

Leave a Reply

Your email address will not be published. Required fields are marked *